how to clean mass air flow sensor chevy equinox

Reliable and quiet your Chevrolet Equinox small crossover SUV is perfect for highway driving and it gets respectable gas mileage as well. How to clean mass air flow sensor chevy equinox.

Symptoms Of A Bad Mass Air Flow Sensor In The Garage With Carparts Com

Mass air flow MAF sensors measure the amount of air entering the engine.

. Place the sensor on a towel for cleaning. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone. Alright enough of the bs.

2018 Equinox Air Box. Part 1 -how To Test The Gm Maf Sensor 31l 34l 43l 50l And 57l. Furthermore detach the connection between the electric connector.

The hood release is located under the dashboard on the drivers side. A bad mass airflow sensor can leave your Chevy Equinoxs engine running rough or even inoperable. 7 Days a Week.

With the Chevy Equinox P0101 means the the Mass Air Flow MAF sensor has a RangePerformance problem. It should be considered a high priority to fix as the MAF sensor not reading properly can really make an impact on the performance of the vehicle. Locate the mass airflow sensor near the engine air filter housing.

Apply the cleaner 10-15 blasts around the inside of the sensor will do. Once disassembled you will have the ability to carry on to the step cleaning the mass air flow sensor of your Chevrolet Express. It passes this information onto your Equinoxs ECU.

This sensor will as time passes get dirty and its two filaments that will give information to your computer on the quality and temperature of the air will no longer be able to collect data accurately it is in this. The goal of this cleaning will be to take out all its harmful particles to allow it to work efficiently again. The most common signs of bad mass air flow sensor MAF in Chevy Equinox are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe.

If you like you can also spray down the sensor with some WD-40. If check engine light code p0171 persists after you have reconnected and replaced all damaged vacuum lines. 1 Year12K Mile Warranty.

Now use the airflow cleaner to spray the plate and clean them. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will remove most of the grime. Mass Air Flow Sensor.

Remove The MAF Sensor From Vehicle. Once it is dry it can be reinstalled and the car can be started again. Now well proceed to the very delicate cleaning of the flow meter.

Remove the air mass sensor cleaner from its container and spray it on the sensor. And lets get started with the actual step by step cleaning of the GM mass air flow MAF sensor Buick Chevrolet Oldsmobile Pontiac and GMC models. The mass air flow sensor is part of the engines intake system and is.

Wipe the leftover cleaner off the inner and outer edges once you have finished spraying it on. Step 3 Clean the MAF Sensor. Remove the mass air flow sensor from the car or truck.

The Intake Air Temperature IAT sensor is also built into. Once off your MAF sensor should look like the one in the photo. Also clean the sides of the part its housing its connectors and its terminals.

This sensor will over time get dirty and its two filaments that will give information to your computer on the quality and temperature of the air will no longer have the ability to collect data correctly it. Your sensor is now fully operational and clean. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will take out most of the grime.

A MAF sensor measures the density of the air entering the intake manifold. Here I demonstrate how I cleaned my manifold absolute pressure MAP sensor and mass air flow MAF sensor in 2012 Equinox with 24L ecotec engine. Let the cleaner sit for a few seconds afterward.

However you should be careful to not scrub the parts as this might end up breaking or damaging the wire. Today I show you where your Mass Air Flow MAF Sensor is located and how to remove and clean it. This automotive maintenance tutorial was specifically written to assist owners of the third generation 2018 2019 and probably also the face-lifted or revised 2020 2021 and 2022 model years GM Chevrolet Equinox SUV in cleaning or changing the MAF mass air flow sensor for the Ecotec 15 liter turbocharged four.

Open the hood of your Chevrolet. The intent of this cleaning will be to remove all its impure substances to allow it to work efficiently again. If you have a hot wire mass air flow sensor make sure the cleaner doesnt get onto the hot wires or plate.

To clean your MAF sensor simply take a solvent and spray it onto a paper towel. Now well proceed to the very delicate cleaning of the flow meter. Chevy equinox 2006 mass air flow sensor by delphi.

Make sure you dry the MAF sensor before fitting it back to the car in the air duct. Unplug the electrical connector from the mass airflow sensor. Then apply the solvent to the wire mesh on the front of the sensor and scrub in a circular motion with an emphasis on any oil residue that may be present.

The mass airflow sensor commonly abbreviated to MAF is one of the most important engine management sensors. We will cover exactly what that means and potential fixes for it below. Once disassembled you will be able to carry on to the step cleaning the mass air flow sensor of your Chevrolet Trax.

7 Days a Week. Press the red clip slightly to unlock it. Remove the screws that hold the mass airflow sensor in place.

Two Screws On Side. Clean your dirty mass air sensor. Ad Have Auto Mechanics Come to You.

Why Would A Car Run Better With The Mass Air Flow Sensor Unplugged Car Truck And Vehicle How To Guides Vehicle Freak